Now the type of poly we picked, well we picked it for a reason. And the reason was that if you re-coat after a certain amount of time, you don't have to sand in between coats. Now, this sounds pretty awesome, because not only does it save a lot of time, but you don't have to rent a buffer. And that is a pretty big draw because buffers are notoriously hard to use (with good reason, I now have experience, but more on that later). We also went with a glossy finish for the first two coats after reading that even if you want to end up with satin or semi gloss finish, you want to start with high gloss so as not to introduce any milkiness to the final look (apparently with some polys the chemicals that caused the less glossy finish can also create a milky look if applied in multiple coats).
So, after the first coat we were feeling pretty good. It had been easier than we were really thinking and we'd gotten done in a reasonable window. We'd done the first coat in the morning so we went and had lunch and came back after about 6 hours.
But here's the thing, we weren't super certain about the timeline for a number of reasons. The can said 8-10 hours at 77 degrees, but a lot of things can affect how fast poly dries, namely: time, temperature, and humidity. We had a time metric, based on the can, and a temperature range of 60-80 (with the example begin at 77), but it didn't say anything about humidity. However, our handy dandy book tells us that the higher the temperature and the lower the humidity, the faster drying occurs. Now we were doing this in Feb, so the temp outside was only 45 and we couldn't turn on the heat because we didn't want to blow dust everywhere. So we were doing our best with a bunch of space heaters but we could only get up to around 65 in the house BUT the humidity that day was low, closer to 30 than the 50 our book recommended. So we figured, low temp slows drying, but low humidity speeds it. Then there was the fact that it had taken us 3 hours to do it. So, we figured, if the max time was 10 hours, and we started in the back, then after about 6 hours after we finished it would be dry enough to walk down teh hall, but not so dry that by the time we were done we'd be over the 10 hour mark. Wheew, its exhausting just writing about it. Needless to say, we probably overthought it, but after 6 hours we came back, tapped on the floor next to the kitchen, and said, what the hell, let's do it.
So, we got all set up again and started over. But here's the thing, it was about 4pm at that point and there were a couple things we didn't bargain on. One was the fading light, not all the rooms have overhead light and overhead light isn't really the best light for this kind of work anyway. And then there was the fact that the sheen for our first coat was glossy. Which meant that I couldn't tell the difference between the new wet application. And that my friends, is a problem. Because if you can't tell where you've put the poly, there's pretty much no way to apply a second coat with any confidence. We soldiered on, but it was tense and not very much fun at all. But we hoped for the best.
Friday, June 3, 2016
Polyurethane coat 1
So, the stained boards have been replaced, the floor has been sanded to the appropriate grit, and we've cleaned it within an inch of its life. Now for the stressful part. Like a big game or onstage performance, we only get one shot at the poly. Well, actually, we get three shots, cause Matt wanted to do three coats. But first, we decided to do a wood sealer because we weren't staining it. The wood sealer helps close the wood grain and keep it from getting "hairy" when you put down the poly. If you've ever gotten raw wood wet, you know what I mean. So, we did that first, using a pad applicator. it wasn't shiny, but it did give it a nice richer color. After it dried, we had to sand it with the pole sander at 320 grit (per the instructions on the can)
Then came the big dance, and of course we had to prepare. We decided that the kitchen would be our exit point and also our prep space. We used the sealer as a practice run for the poly, but since this stuff soaks into the wood and dries in two hours, it wasn't a perfect dry run. It was enough for us to validate our idea of starting in the master and working our way through the other bedrooms, down the hall, through the living room and dining room and then exiting through the kitchen.
Then came the big dance, and of course we had to prepare. We decided that the kitchen would be our exit point and also our prep space. We used the sealer as a practice run for the poly, but since this stuff soaks into the wood and dries in two hours, it wasn't a perfect dry run. It was enough for us to validate our idea of starting in the master and working our way through the other bedrooms, down the hall, through the living room and dining room and then exiting through the kitchen.
So we set up the space with everything we would need and then got started. We carefully mixed the poly, trying not to introduce bubbles. Then we strained it into that large black bucket you see in the foreground. (We also tried putting it in a regular paint pan, but the bucket ended up being the way to go in the end). Then we put on our little booties to protect the floor from our feet and started in the master bedroom. We tried both a lambs applicator and a synthetic roller and decided that we liked the roller better. It was easier to apply an even layer and didn't shed as much. (writing this makes it sound like we had a clear headed rational decision, but in reality there was a lot of anxiety, shouting, and swearing involved because we were making the decision in the midst of applying poly, which was drying as we were deciding, nevertheless, our recommendation stands). Once we got going, it was actually pretty easy, Matt did the edging with a brush, and I rolled away. It took a little over 3 hours, including the switching back and forth at the beginning between the applicators. I felt pretty good when we got done, it looked really nice:
Cleaning the floor
So as you might imagine, we created a lot of dust with all that sanding. And dust + polyurathane = bumpy floors. So before putting down the poly we had to get all the dust off. And I mean all of it. We started by wiping down the ceiling. Laugh all you want, but it was dusty! Then we did the walls and then the floor. We used a swiffer to begin with and that worked well on the ceiling and walls, but when we got to the floor they started getting chewed up. So we used the microfiber clothes and that worked well.
Now, what we didn't do, and what we learned later we should have, was to use a rag soaked in mineral spirits to do the final pass, basically just t-shirt material dipped in in, not dripping, but wet. How did we learn this little gem? more on that later...
Floor refinishing, the big boy part 2
So, lets recap so far
1. Multi-head orbital didn't have enough ummph
2. Big boy drum sander with 36 grit, diagonal (sometimes twice) and then straight
3. Edger with 36 grit
But, the trick is, we have to get to 100 grit to put down poly. So, you guessed it, we've got a couple more passes to make. Each room has to have the big boy at 60, then edged at 60, then the big boy at 80, and then edged at 80. But we hate the edger and it was leaving these swirly patterns. So we decided to go with a hand held random orbiter. Now, this is not really a recommended choice anywhere that we found, but we figured it was sort of like the large multi orbital except smaller... so we went with it. Unfortunately, the 60 grit wasn't getting rid of the swirly stuff left by Heath Edger, so we had to go back to 40 grit before going up to 60 grit.
So the pattern went like this
4. Hand held orbital edging with 40 grit
5. Dust the floor - yep, this is what it sounds like. Our book recommended this because when you sand, you not only create wood particles of a certain size, but the sandpaper itself can also shed grit. And if you get a particle the size of 36 grit on your 60 grit paper, well, it'll gouge the crap out of the floor. So, dusting is necessary. We tried a swiffer but the surface was too rough, so we got a pack of microfiber clothes and attached them to the swiffer pole. Worked like a charm :)
6. Big boy with 60 grit
7. Edge with 60 grit
8. Dust the floor
Oh, and then, I almost forgot. We had tons of holes in the floor. Mostly from an old carpet install which meant nail holes around the edges where the tack strips were and staples in the middle of the room where they tacked down the padding. So we spend time after the 60 grit step putting in wood putty in all of the places that needed it so that the 80 grit step would level it down. Ok, back to the steps:
9. Fill with wood putty
10. Big boy with 80
11 Edge with 80
And here's where things get interesting, so I mentioned above that we had to get to 100 grit per the recommendation of the polyurathane, but they don't make 100 grit paper for the drum sander. So for the edges, we're fine, but for the 100 grit... well, our options were limited. A buffer would work, in theory, but after calling around, none of the places that would rent a buffer had 100 grit screens for them, only 120. And some of the literature we read said that poly might not stick properly if the wood was sanded too finely. So we put on our creative pants again and decided to pole sand. Yes, you read that right, we put 100 grit sand paper on a pole sander and went to town. Once we were done with that, the only thing left was cleaning.
1. Multi-head orbital didn't have enough ummph
2. Big boy drum sander with 36 grit, diagonal (sometimes twice) and then straight
3. Edger with 36 grit
But, the trick is, we have to get to 100 grit to put down poly. So, you guessed it, we've got a couple more passes to make. Each room has to have the big boy at 60, then edged at 60, then the big boy at 80, and then edged at 80. But we hate the edger and it was leaving these swirly patterns. So we decided to go with a hand held random orbiter. Now, this is not really a recommended choice anywhere that we found, but we figured it was sort of like the large multi orbital except smaller... so we went with it. Unfortunately, the 60 grit wasn't getting rid of the swirly stuff left by Heath Edger, so we had to go back to 40 grit before going up to 60 grit.
So the pattern went like this
4. Hand held orbital edging with 40 grit
5. Dust the floor - yep, this is what it sounds like. Our book recommended this because when you sand, you not only create wood particles of a certain size, but the sandpaper itself can also shed grit. And if you get a particle the size of 36 grit on your 60 grit paper, well, it'll gouge the crap out of the floor. So, dusting is necessary. We tried a swiffer but the surface was too rough, so we got a pack of microfiber clothes and attached them to the swiffer pole. Worked like a charm :)
6. Big boy with 60 grit
7. Edge with 60 grit
8. Dust the floor
Oh, and then, I almost forgot. We had tons of holes in the floor. Mostly from an old carpet install which meant nail holes around the edges where the tack strips were and staples in the middle of the room where they tacked down the padding. So we spend time after the 60 grit step putting in wood putty in all of the places that needed it so that the 80 grit step would level it down. Ok, back to the steps:
9. Fill with wood putty
10. Big boy with 80
11 Edge with 80
And here's where things get interesting, so I mentioned above that we had to get to 100 grit per the recommendation of the polyurathane, but they don't make 100 grit paper for the drum sander. So for the edges, we're fine, but for the 100 grit... well, our options were limited. A buffer would work, in theory, but after calling around, none of the places that would rent a buffer had 100 grit screens for them, only 120. And some of the literature we read said that poly might not stick properly if the wood was sanded too finely. So we put on our creative pants again and decided to pole sand. Yes, you read that right, we put 100 grit sand paper on a pole sander and went to town. Once we were done with that, the only thing left was cleaning.
Thursday, April 7, 2016
Floor refinishing, the edger
So, once we got done with the 36 grit at a diagonal and then 36 straight with the drum sander, it was time to move on to other grits. But the thing about drum sanders, and part of the reason we decided to go with an orbital is that the drum sander can't get close to the walls or in tight spaces (orbitals can). So you and entirely different piece of equipment called an edger to get in the tight spaces. Now, what we didn't know is that "edger" is code for "torture device". They look sort of innocuous, kind of like a shiny, spaceship on wheels
The thing is, they weigh, like 50 lbs. Or maybe not 50, but a lot. And you aren't supposed to press down on them, and they are only about 2 ft off the ground, so what you end up with is a hunched over process where you are trying to keep the thing moving while balancing precariously. I tried it, Matt tried it, it was hard, really hard. And with 36 grit, you can really mess up the floor because the disc spins in one direction and you can "dish out" the floor in a circular pattern. Especially if you are moving against the grain, which inevitably you have to do in the places where the floor butts into the wall (as opposed to the places where the boards go along the wall). But, then Jimmy to the rescue. And let me tell you, he was awesome at it. our book recommended a J patter where you use the edger to go with the grain as far as possible and then turn at the last possible second next to the wall at the butt ends. Dad was a real trooper because he basically did 80-90% of the edging. And with 100 square feet, three bedrooms, 5 closets, a living room, and a dining room, that's a lot of edging.
After that, all that was left was the very extremes of the corners, which you get to either with a hand held scraper or a triangular sandpaper head for a multi tool (we used both, and they each had advantages). Scrapers are basically hand held razor blades that you, yes, scrap against the floor. The advantage is that you can really feel what you are doing and easily control the blade. But it's hard word. The one we got looked basically like this:
You basically put one hand on the handle, and one hand on the knob, and the angle and pressure control how much you take off.
The triangular sander on the other hand, makes short work of anything, but its really easy to go too far and take off too much (or at least that's what Mom said because honestly, she did all of the work with the multi-tool) Do I have amazing parents? Yes, absolutely.
The thing is, they weigh, like 50 lbs. Or maybe not 50, but a lot. And you aren't supposed to press down on them, and they are only about 2 ft off the ground, so what you end up with is a hunched over process where you are trying to keep the thing moving while balancing precariously. I tried it, Matt tried it, it was hard, really hard. And with 36 grit, you can really mess up the floor because the disc spins in one direction and you can "dish out" the floor in a circular pattern. Especially if you are moving against the grain, which inevitably you have to do in the places where the floor butts into the wall (as opposed to the places where the boards go along the wall). But, then Jimmy to the rescue. And let me tell you, he was awesome at it. our book recommended a J patter where you use the edger to go with the grain as far as possible and then turn at the last possible second next to the wall at the butt ends. Dad was a real trooper because he basically did 80-90% of the edging. And with 100 square feet, three bedrooms, 5 closets, a living room, and a dining room, that's a lot of edging.
After that, all that was left was the very extremes of the corners, which you get to either with a hand held scraper or a triangular sandpaper head for a multi tool (we used both, and they each had advantages). Scrapers are basically hand held razor blades that you, yes, scrap against the floor. The advantage is that you can really feel what you are doing and easily control the blade. But it's hard word. The one we got looked basically like this:
You basically put one hand on the handle, and one hand on the knob, and the angle and pressure control how much you take off.
The triangular sander on the other hand, makes short work of anything, but its really easy to go too far and take off too much (or at least that's what Mom said because honestly, she did all of the work with the multi-tool) Do I have amazing parents? Yes, absolutely.
Wednesday, April 6, 2016
Floor refinishing, the big boy part 1
So, having admitted defeat with the orbital, we pulled on our big boy pants and went to get a big boy tool. We tried to do some research on different types and brands, but honestly, there isn't much out there. So, in the face of no information we decided to go with what we did know. There's a new Menards in town, and they rent drum sanders, and those drums sanders are pretty new, because the store is pretty new. So we decided we'd do that.
Turns out, the drum sander isn't so scary. One website we went to recommended you use the lightest grit you can find to practice. In our case this was 80 grit and this seemed like good advice, so that's what we did. When using the drum sander the MOST important thing is to ALWAYS keep it moving when it is running and touching the floor. Now the great thing is that most new machines come with a clutch that allows you to raise and lower the drum after you get it started. The trick is to start moving forward (or backward) before lowering the clutch. After the first few tries with the 80, we got the hang of it pretty well. So, we switched to 36 and started going for it.
We decided to start in the master bedroom
And we got as far in 30 minutes as we did in 7 hours with the orbital.
Turns out, the drum sander isn't so scary. One website we went to recommended you use the lightest grit you can find to practice. In our case this was 80 grit and this seemed like good advice, so that's what we did. When using the drum sander the MOST important thing is to ALWAYS keep it moving when it is running and touching the floor. Now the great thing is that most new machines come with a clutch that allows you to raise and lower the drum after you get it started. The trick is to start moving forward (or backward) before lowering the clutch. After the first few tries with the 80, we got the hang of it pretty well. So, we switched to 36 and started going for it.
We decided to start in the master bedroom
And we got as far in 30 minutes as we did in 7 hours with the orbital.
It sort of looks like Matt is doing a happy dance in the photo. I'm not sure if he was or not, but for the sake of the story, I'm going to say he was :).
Now, using the drum sander has a very specific formula. First of all, one pass is forward AND backwards. It's actually almost easier to walk backwards and pull it behind you. Also, you need to overlap passes, so that each bit of the floor gets actually 4 passes ( 1 forward and back, and then an overlap, forward and back). We actually put a piece of tape on the front of the drum and drew a line on it, so that we'd know where the center was. In addition to that, if your floor is very bad, like ours was, you will want to take at least one pass at a 7-25 degree angle to the floor boards. Because an angle cut is more aggressive than along the grain, this helps level the floor. If your floors aren't crazy bad, you might be able to get away with doing the diagonal at 60 grit, but with our cupped boards and old varnish, we weren't so lucky. But a diagonal at 36 did the trick (actually, in a few places, we had to do more than one diagonal pass at 36), but the point with 36 grit is to get all the varnish off.
With the big boy, it only took a day for us to get all the varnish off, even with the extra diagonal passes. Also, pro tip here, if you do a diagonal pass with a grit, you must go over it with the grain with the same grit. A lot of people will skip this step, thinking the next grit will take out the cross grain scratches, but in general, it won't. And honestly, with the drum sander, it doesn't take that long ot do it right.
Floor refinishing, our tryst with the multi head orbital
Sounds dirtier than it is, I promise.
Now, if you are going to refinish a floor, the most obvious part of the process is that you have to get the old finish up (closely tied for "most obvious" with needing to put down new stain"). In the olden days, there was really only one way to do this, a drum sander. But drum sanders have a fairly scary reputation (more on this later). So, for the do it yourselfer, a few years ago there emerged another, safe option:the multi-disc orbital. And after much reading, and researching, we decided this was the way to go, because pretty much everything we read said it was practically foolproof. So, we found a recommended brand, and a place that carried them, and one Saturday morning a few weeks ago, we went and picked on up our very own, which looked like this:
And a during, Matt's sort of buried in the closed here but you can see the pattern we started with:
Now, if you are going to refinish a floor, the most obvious part of the process is that you have to get the old finish up (closely tied for "most obvious" with needing to put down new stain"). In the olden days, there was really only one way to do this, a drum sander. But drum sanders have a fairly scary reputation (more on this later). So, for the do it yourselfer, a few years ago there emerged another, safe option:the multi-disc orbital. And after much reading, and researching, we decided this was the way to go, because pretty much everything we read said it was practically foolproof. So, we found a recommended brand, and a place that carried them, and one Saturday morning a few weeks ago, we went and picked on up our very own, which looked like this:
now if you were to tip that puppy back, you'd see that it has four round discs on the bottom. This discs spin around, but the also oscillate in a random pattern so that the scratches don't all appear in the same direction. This is in contrast to the drum sander above, which only sands in line with the direction of the drum. Because of the random oscillation, you kinda can't mess it up. And if it sits in the same place on the floor, well, that't not a problem either. So all signs pointed to this being the machine for us.
Unfortunately, the place we rented from was pretty busy and the guy that helped us was, and I quote, "not a floor guy" so they were pretty sparse with the help. No manual, no nothing and we had to ask for help. I would not recommend them. But, the machine was supposed to be foolproof, so we went ahead. We bought a ton of packs of round disc paper, lugged the thing home and up the stairs, and decided the back bedroom was the best place to start.
We have the requisite before picture:
And a during, Matt's sort of buried in the closed here but you can see the pattern we started with:
And after 7 hours of hard work, we were here, sigh:
As you can see from the variegated color still on the floor, we didn't get all the old varnish off. We read in the books that if your floor is in good shape, you can start with 60 grit. We figured, our floors weren't amazing, so we started with 40. And that got us about a 3x6 ft square using one set of pads. So, we changed the pads a bunch, and kept going, because at that point what did we have to lose? But after a lot of time, we basically had to admit defeat. Not only did we not buy nearly enough pads to do the rest of the house, but it would have taken us about two weeks to finish it up, and at more than a dollar per sandpaper pad, and four pads on the machine at a time, it would have cost a fortune.
But, we did learn a lot. First of all, the machine is foolproof. And very easy to use. You basically just turn in on and it does all the work. Secondly, our floor wasn't in sort of bad shape. It was in BAD shape. You can't really see from the pictures, but we had some major issues with cupping of the floorboards. Cupping (and crowing) occurs when the moisture content above and below the floorboards is different. You can see it really easily in water damaged spots, but we had it all over our floor. Probably because our lower level is a basement. In any case, cupping is when the middle of a board is lower than the edges (crowning is the opposite, where the edges turn down). All of this meant that the random orbital, because it was flat and not very aggressive, couldn't get at the places that were lower.
Long story short, if your floor is not absolutely flat, you don't want the easy way out. You need the big boy sander. Which is what we did the next weekend.
Subscribe to:
Posts (Atom)

















